@article { author = {Poursaeidi, Esmaeil and Javadi Sigaroodi, MohammadRasoul and Rahimi, Javad and taleghani, mohammadhasan and Fartash, Amir hosein and Yousefi, Yousef and noorsina, Saba}, title = {The investigation of change in thermal conductivity of porous coatings during the aging process}, journal = {Journal of Aeronautical Engineering}, volume = {23}, number = {1}, pages = {97-108}, year = {2021}, publisher = {Shahid Sattari Aeronautical University of Science and Technology-Iranian Aerospace Society Director-in-Charge: Dr. Akbar Cheraqi Editor-in-Chief: Dr. Farhad Javidrad Associate Editor: Dr. Vahid Khalafi Website Manager: Amir Ehsan Zamanian Eng. Nima Mansour Lakouraj English Text Editor: Dr. Roohollah Maleki}, issn = {17359449}, eissn = {17359449}, doi = {10.22034/joae.2021.139485}, abstract = {Exposure of the TBCs layers to high temperatures for a long time causes sintering in the ceramic layer, resulting in changes in the porosity. Since the thermal conductivity of air in the porosity of the layers is much lower than the ceramic material in the coating, a decrease or increase in the percentage of porosity will end up with changes in the conductivity of the layer, which subsequently affect the overall efficiency. In this study, a TBC was first applied to the prepared samples from Inconel738 turbine blades. The samples were subjected to an aging process in the furnace for a specified time. The porosity changes in the ceramic layer of the coating during the aging process were investigated using image processing of the SEM images. The porosity of the images obtained from SEM and thermal conductivity in different porosities were determined by OOF2 and ImageJ software, respectively. To validate the numerical results, temperature distribution on the thermal barrier coatings is obtained by the analytical solution of the Fourier equation. According to the analysis performed on the SEM images gathered from the samples during different aging hours, it is observed that by increasing the aging hours during 48 hours, the percentage of porosity of the whole ceramic layer decreased by 8%. According to the results, by decreasing porosity in the ceramic layer, an increase in thermal conductivity has been observed, followed by an increase in the substrate's temperature and a decrease in the overall performance over time.}, keywords = {Thermal Barrier Coatings,Thermal conductivity,porosity,ImageJ,OOF2}, title_fa = {بررسی میزان رسانش پوشش های متخلخل در طی فرآیند پیرگرمایی}, abstract_fa = {قرارگیری پوشش‌های سد حرارتی در دما بالا، باعث ایجاد پخت در لایه سرامیکی شده و این امر تغییرات درصد تخلخل را همراه دارد. با توجه به این موضوع که ضریب رسانش حرارتی هوا موجود در تخلخل لایه‌ها بسیار کمتر از مواد سرامیکی موجود در پوشش است،‌ کاهش و یا افزایش تخلخل تغییرات ضریب رسانش پوشش را به دنبال خواهد داشت که این امر بر عملکرد کلی لایه‌های پوشش، تأثیر مستقیم دارد. در این پژوهش ابتدا بر روی نمونه‌های تهیه شده از پره توربین از جنسInconel738، پوشش سد حرارتی اعمال شد و سپس نمونه‌ها در مدت زمان مشخص در داخل کوره تحت فرآیند پیرگرمایی قرار داده شدند. تغییرات تخلخل موجود در لایه سرامیکی پوشش در طی فرایند پیرگرمایی با استفاده از پردازش تصاویر SEM بررسی شد. درصد تخلخل موجود در تصاویر به دست ‌آمده از SEM در نرم‌افزار ImageJ تعیین شده و در نرم‌افزار OOF2 ضریب رسانش حرارتی در تخلخل‌های مختلف به صورت عددی محاسبه شد. به منظور صحت سنجی نتایج عددی، توزیع دما بر روی پوشش‌های سد حرارتی با حل تحلیلی معادله انتقال حرارت فوریه به دست آمد. مطابق آنالیز تصاویر SEM به دست آمده از نمونه‌ها طی ساعات پیرگرمایی مختلف، مشاهده شد که با افزایش ساعات پیرگرمایی در طی ۴۸ ساعت، درصد تخلخل کل لایه سرامیکی ۸٪ کاهش داشته است. مطابق نتایج به دست آمده با کاهش تخلخل در لایه سرامیکی افزایش ضریب رسانش حرارتی مشاهده می‌شود که این امر باعث افزایش دمای بستر شده و به مرور زمان عملکرد اصلی این نوع پوشش‌ها را کاهش می‌دهد.}, keywords_fa = {پوشش‌های سد حرارتی,ضریب رسانش حرارتی,تخلخل,ImageJ,OOF2}, url = {https://www.joae.ir/article_139485.html}, eprint = {https://www.joae.ir/article_139485_cc0c1346b7e61990c25cf6c51c5bac67.pdf} }